Blade protection size:
For a sword measuring 64 cm
Blade protection for assembly onto a pair of gripping pliers
The blade protection can be mounted onto your pair of gripping pliers by means of four oblong holes. After that, the Cutmaster Speed and a suitable lubricating oil tank can be mounted to the blade protection. The size is adapted to the specified sword length. If a larger sword is to be mounted, this is also possible. The sword then sticks out of the guard at the front.
Blade protection size:
For a sword measuring 64 cm
Blade protection for assembly onto a pair of gripping pliers
The blade protection can be mounted onto your pair of gripping pliers by means of four oblong holes. After that, the Cutmaster Basic and a suitable lubricating oil tank can be mounted to the blade protection. The size is adapted to the specified sword length. If a larger sword is to be mounted, this is also possible. The sword then sticks out of the guard at the front.
Chain wheel sprockets
Available in various pitches
Pitch 12, 13, 14, 15, 16
Pitfch 14 is the standard in our Cumaster Basic.
Pitfch 14 is the standard in our Cumaster Speed.
Pitfch 14 is the standard in our Cumaster Electro.
The chain sprockets all have a pitch of 404 and a 25 mm borehole with featherkey notches.
Hydraulically driven chainsaw
The Cutmaster Basichas been specially developed for use in cutting devices and firewood harvesters.
The saw can be supplied with various sizes of powerful hydyraulic motors which drive the chain with a cutting speed of 20m/s.
Due to the large selection of sword lengths (54cm to113cm) the Cutmaster Basic can be used very variably. The chain is tensioned by a set screw and lubricated by the integrated lubrication system.
The Cutmaster Basic is equipped with a hdraulic swivel system..
- Integrated chain lubrication- 20 metres/sec cutting speed- chain pitch 0.404".- chain wheel with 14 dents- left-hand and right-hand design- hydraulic swivel device- swivel axis in the motor shaft- robust stainless steel construction
Motor size:
5KW
|
Swivel direction:
to the left
|
Swivel system:
Hydraulical (hydraulic cylinder)
Electrically driven chainsaw
The Cutmaster Electronic has been specially developed for use in cut-to-length devices and automatic splitting machines.
The saw is available with powerful electric motors from German manufacturers in various sizes, which drive the chain at a cutting speed of 20 m / s.
The chain is tensioned by a set screw and lubricated by the integrated lubrication system.
The Cutmaster Elektro is equipped with a hydraulic swivel system.
- Integrated chain lubrication- 20 m/sec cutting speed- chain pitch 0.404".- AC motors made by German manufacturers- Chainwheel with 16 dents- By means of frequency converters you can increase the speed- Hydraulic swivel device- Swivel axis in the motor shaft- Robust design
Lubrication oil tank:
Not specified
|
Motor size:
6ccm
|
Swivel direction:
to the right
|
Sword length:
Iggesund 54 cm
Hydraulically driven chainsaw
The Cutmaster Speed has been specially developed for use in cutting devices and firewood harvesters.
The saw can be supplied with a powerful Parker axial piston motor, two sizes of which are available. This motor drives the chain with a cutting speed of up to 60 metres/s.
Motor size 6ccm: 50 KW – 67 litres/min (at 400bar)
Motor size 10ccm: 85 KW – 110 litres/min (at 400bar)
While the motors do not have to be driven with a 400 bar pump, please bear in mind that in case of a 200 bar pump, only half the capacity can be reached while the speed remains unchanged.
Due to the large selection of sword lengths (54cm to 135cm), the Cutmaster Speed can be used very variably. The chain is tensioned by a set screw and lubricated by the integrated lubrication system.
The Cutmaster Speed is equipped with a hdraulic swivel system.
- Integrated chain lubrication- 40 metres/sec cutting speed- chain pitch 0.404".- chain wheel with 13 dents- left-hand and right-hand design- hyraulic swivel device- swivel axis in the motor shaft- robust stainless steel construction
- Axial piston motor with 10,000 rpm
- loadable up to 400bar
Grapple saw Cutmaster Basic
The grapple saw may be attached to different grippers on excavators, cranes or front loaders. For this purpose, three different sizes are available.
The saw as well as the lubrication oil tank are mounted in the blade protection which can be attached to your gripper via oblong holes.
The size of the sword protection is adjusted to the length of your blade. Should you wish to mount a longer sword, this is possible. The blade then protrudes from the front of the protection.
The saw is equipped with a powerful 9.3 kW hydraulic motor which drives the chain to a cutting speed of 20.3 metres/s. At full speed the motor requires 31.5 litres of hydraulic oil per minute.
Upon request also available with other engine sizes.
6 KW (21 litres/min)9.3 KW (31.5 litres/min)14.4 KW (50.4 litres/min)Available blade lengths:54cm64cm75cmThe insert length is the sword length - 10cm
Scope of Supply:
- Cutmaster Basic (with the chosen motor size)
- Blade protection adjusted to the chosen blade length
- 1 blade
- 1 chain
Blade protection size:
For a sword measuring 64 cm
|
Motor size:
6ccm
Grapple saw Cutmaster Speed
The grapple saw may be attached to different grippers on excavators, cranes or front loaders. For this purpose, three different sizes are available.
The saw as well as the lubrication oil tank are mounted in the sword protection which can be attached to your gripper via oblong holes.
The size of the sword protection is adjusted to the length of your blade. Should you wish to mount a longer sword, this is possible. The blade then protrudes from the front of the protection.
The saw can be supplied with a powerful Parker axial piston motor, two sizes of which are available. This motor drives the chain with a cutting speed of up to 60 m/s.
Size of motor 6ccm: 50 KW – 67 litres/min (at 400bar)
While the motors do not have to be driven with a 400 bar pump, please bear in mind that in case of a 200 bar pump, only half the capacity can be reached while the speed remains unchanged.
Available sword lengths:54cm64cm75cmThe insert length is the sword length -10cm
Scope of supply:
- Cutmaster Speed (with the chosen motor size)
- Blade protection suitable for the chosen blade length
- 1 blade
- 1 chain
Lubrication oil tank for assembly in the blade protection
The lubricating oil tank has been developed to fit perfectly into our blade protection. The tank holds approx. 1 l of lubricating oil.
Lubrication oil tank for direct assembly
The lubricating oil tank can be mounted directly on the Cutmaster Basic, Speed or Electric.The tank holds approx. 1 l of lubricating oil.
Micro throttle valve
The micro throttle valve is perfectly suitable wherever precise control is required for small volume flows.The integrated non-return valve throttles the volume flow from 'A' to 'B', while there is free flow from 'B' to 'A'.
Connections: G1/8"
The throttle is used to adjust the swing speed of the saw.
Pressure reducing valve
Functionality
Once the pressure in 'U' is reached, the valve blocks the passage between 'E' and 'U' to keep the pressure 'U' constant.If the pressure in 'U' is exceeded, it can be relieved via 'Dr'. This does not influence the upstream pressure in 'E'.
Since it is a single-acting valve, it allows a free oil return from 'U' to 'E'
Adjustment range from 5 to 50 bar.
Connections: G3/8"
The pressure reducing valve is used to adjust the pressure on the swing cylinder.
Chain length:
For sword measuring 54 cm
|
Size of sprocket:
12 teeth
The chains are suitable for all our saws.They have got a 404 division and the chain size is 2 mm.
We exclusively use quality chains (half chisel) made by the Stihl coppany.
Saw-bar
The saw swords are suitable for all our saws. With the Harvester pitch of 404, the necessary stability is achieved. The specified length is the total length, some 10 cm of which are needed for clamping in the saw.
This means that e.g. the available lengh of a sword measuring 75 cm is approx. 65 cm.
Set of hydraulic flanges for Vivoil motor
The set of hydraulic flanges consists of a flange for the pressure side with a 1/2" female thread and a flange for the return side with a 3/4" female thread.
The flanges are screwed onto the motor of the Cuatmaster Basic. Following that, your hydraulic hoses are connected to the flanges.
Welding holder for the Cutmaster Basic
The holder is suitable for firewood harvesters or cutting units. It is simply welded onto your construction and then the saw can be mounted.
The holder has got a thickness of 10 mm.
Welding holder for the Cutmaster Speed
The holder is suitable for firewood harvesters or cutting units. It is simply welded onto your construction and then the saw can be mounted.
The holder has got a thickness of 10 mm.
€55.00*
This website uses cookies to ensure the best experience possible. More information...
